Keysight Technologies N5252A User Manual Download Page 8

Page: 8 / 62

Verifying Your Shipment of N5252A and N5253E

Table 1

N5252A-200 and N5252A-400 Bundle

M9005A Option 002, PXIe 5-slot Chassis with opt.
PCIe card and I/O cable for tower computer.

Description

Quantity for -200

Quantity for -400

M9374A with Option 551, PXIe Network Analyzer,
300 kHz- 20 GHz (installed into M9005A PXIe Chassis).

N5252AW12 Option 201 (N5252-80002) a pair of
TxRx VNAX modules from VDI with 1.2m cable sets in
one Pelican case.

N5262AC12 Calibration Kit, 60-90 GHz.

Table 2

N5253E1 Bundle

P5024A-400 Vector Network Analyzer, 9 kHz-20 GHz,
4-port.

Description

Quantity

N5262AC12 Calibration Kit, 60-90 GHz.

N5252AW12 Option 201 (N5252-80002) a pair of
TxRx VNAX modules from VDI with 1.2m cable
sets in one Pelican case.

S97560B - Operation with N5252AW12 frequency
extenders from VDI.

Refer to your box contents list supplied with your shipment.

N5252-90002 User's Guide

Summary of Contents for N5252A































































Search results

Summary of Contents for N5252A

Reviews:

Related manuals for N5252A

Brands by name

Popular brands

Keysight Technologies N5252A, User Manual

Search results

Summary of Contents for N5252A

Reviews:

Related manuals for N5252A

Brands by name

Popular brands