manualshive.com logo in svg

Keysight Technologies N5252A, User Manual

Share
Download
Keysight Technologies N5252A User Manual Download Page 23

System Setup for N5253E

To use your VNA as a standard 20 or 50 GHz VNA,  test set cables are 
available for separate purchase. See the recommended cables in the 

Banded Millimeter Wave Analysis Technical Overview

. 

1. Connect the P500xA Series USB VNA to your computer with the supplied

USB-C 3.0 cable. Refer to the 

P5000A Series Quick Start Guide

.

2. Connect the supplied power cord to the VNA power supply and to the

VNA, but do not apply power until the system setup is complete.

3. Ensure the jumper cable (LO In to LO Out), black control cable (CTRL S to

CTRL M), and 50 Ω load (LO In) are installed. See Figure 13 and 14 below
and the configuration drawings in the next three pages for details.

Figure 13 

P5024/8A - Jumper Cable and Control Cable Connections

1

 

Figure 14 

P5004A to P5008A - Jumper Cable and Control Cable Connections

1. P5028A shown

This section will aid in connecting your system. For computer setup and software, see 

Computer Setup and Software Installation for N5253E

 

on page 27

.

5. Proceed to 

N5253E Configuration on page 27

 to connect your extenders.

N5252-90002 User's Guide

23

Summary of Contents for N5252A































































Reviews:

No comments

Brands by name

Popular brands

Load more brands