manualshive.com logo in svg

Keysight Technologies N5252A, User Manual

Share
Download
Keysight Technologies N5252A User Manual Download Page 43

Alternative System Configurations

Alternative system configurations can be configured with PXI or USB VNA. Refer to the 

Banded Millimeter Wave Network Analysis Technical Overview

 for more details:

1. System configuration with P937x (see 

Figures 33 and 34)

.

2. 4-Port system configuration with Streamline USB VNA (see 

Figures 37 and 38

).

3. System configuration with N5252APXI test set and PXI or Streamline VNA with 

N5262BWxx standard extenders (see 

Figures 35 and 36

). 

N5252A/N5253Ex E-Band Bundle

 Alternative Configurations

•

The N5252A and N5253E2 allow a 1-port system to be configured. Two 1-port systems 
can be configured and operated separately. The VNA application will still show two 
ports, even when a second port is not configured. Only use 1-port in calibration and 
measurements. The N5253E1 and N5253E3 can be used to make 1-port measurements, 
but cannot be configured into two 1-port systems.

•

A 4-port system can be configured with N5253E1 or N5253E3 by adding one more
4-port Streamline VNA and another pair of the frequency extenders. 

For alternative system configurations with the P9374/75A VNA, the firmware will need to be 
changed to 

A.14.10.13

. Refer to the 

N5252A Support page

 for drivers, firmware, and software. 

The  S97551B (Option 551) multiple instruments measurement is required for one of the 
Streamline VNA in the system to operate.

Frequency 

Extenders for WR15 to WR3.4 mm-Wave Frequency Bands

•

N5252AWxx frequency extenders are available for V, E, W, and D (WR6.5) bands.

•

N5262BWxx frequency extenders with the N5252APXI test set can be configured up 
to WR3.4.

•

N5262ACxx waveguide calibration kits are available for each band (C15 - C03).

•

VNAs need to be ≥ 14 GHz for WR15 (V Band) and ≥ 20 GHz for higher frequency 
bands.

Streamline 

and PXI VNA Requirements

•

Software license S97560B is required for P50xxA to allow configuration for a mm-
wave VNA (not required for P937x).

•

Software license S97551B is required for systems with two Streamline VNAs such as 
N5253E2 or 4-port configurations with two P502xAs.

•

You cannot configure a 4-port system with multiple P500xA or P937xA 2-port 
Streamline VNAs, as only two USB connections are allowed.

•

You can configure a 4-port system with two P502xA 4-port VNAs.

•

You can use P937xAs for up to WR6.5 band systems and P50xxAs for up to WR3.4 
band systems.

•

P502xA cannot be configured into two separate 1-port systems. 

N5252-90002 User's Guide

43

Summary of Contents for N5252A































































Reviews:

No comments

Brands by name

Popular brands

Load more brands