Keysight Technologies N5252A User Manual Download Page 57

Page: 57 / 62

The opening of covers or removal of parts may expose dangerous voltages.

Disconnect the instrument from all voltage sources while it is opened.

Danger of explosion if battery is incorrectly replaced. Replace only with

the same or equivalent type recommended. Discard used batteries

according to manufacturer’s instructions.

Procedures described in this document may be performed with power

supplied to the product while protective covers are removed. Energy

available at many points may, if contacted, result in personal injury.

The power cord is connected to internal capacitors that may remain live for

10 seconds after disconnecting the plug from its power supply.

For continued protection against fire hazard, replace line fuse only with

same type and rating. The use of other fuses or material is prohibited.

The detachable power cord is the instrument disconnecting device. It

disconnects the mains circuits from the mains supply before other parts of the

instrument. The front panel switch is only a standby switch and is not a LINE

switch (disconnecting device).

N5252-90002 User's Guide

Summary of Contents for N5252A































































Search results

Summary of Contents for N5252A

Reviews:

Related manuals for N5252A

Brands by name

Popular brands

Keysight Technologies N5252A, User Manual

Search results

Summary of Contents for N5252A

Reviews:

Related manuals for N5252A

Brands by name

Popular brands