Keysight Technologies N5252A User Manual Download Page 27 | Manualshive

Page: 27 / 62

background image

1.

Keysight IO Libraries Suite

- Download and install the

Keysight IO Libraries Suite

from Keysight's website.

2.

Vector Network Analyzer software

- To download your application firmware, visit

P5000A Keysight Streamline USB Vector Network Analyzer, 4.5 GHz product

Disable "Sleep Mode" on your PC when running the Network Analyzer
application. Leaving it on will cause the application to crash.

There are two software items that need to be installed onto your computer:

• Keysight IO Libraries Suite
• Vector Network Analyzer software (Rev.

A.15.20.0

5

or greater)

Computer Setup and Software Installation for N5253E

P5000A Series USB-Vector Network Analyzer Quick Start Guide (9018-04801)

N5252-90002 User's Guide

27

«
...
25
26
27
28
29
...
»

Summary of Contents for N5252A































































Reviews:

No comments

Related manuals for N5252A

Brand: 3M Pages: 2

Brand: 3M Pages: 16

Brand: Kane Pages: 16

Brand: Bacharach Pages: 48

Brand: Bacharach Pages: 24

Brand: Macnaught Pages: 14

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 4

Brand: Hanna Instruments Pages: 2

Clavinova CVP-805

Brand: Yamaha Pages: 112

Clavinova CLP-270

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 3

Brand: Orange Electronic Pages: 21

Brand: Velleman Pages: 107

Brand: Kawai Pages: 72

Brand: Fluke Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands