![background image](http://html2.mh-extra.com/html/karcher/sb-mu/sb-mu_original-instructions-manual_4691561070.webp)
-
33
Interruptions in water preparation
Fault
Possible cause
Remedy
By whom
Base exchanger is
not regenerating
No power supply
Check power supply (fuse, plug, switch).
Operator/Cus-
tomer Service
Hardness sensor defective
Check hardness sensor, replace if required
Customer Ser-
vice
Water remains
hard after regener-
ation
No salt in the salt tank
Fill up salt, do not allow the salt level to fall below the
water level.
Operator
Injector filter is blocked
Clean the filter
Customer Ser-
vice
Water flow to the salt tank is inadequate
Check the brine filling duration; clean the brine filling
aperture, if required.
Customer Ser-
vice
Rising pipe is leaky
Check rising pipe, pilot pipe
Customer Ser-
vice
too high salt con-
sumption
too much water in the water tank
see below
Customer Ser-
vice
wrong salt quantity setting
Check salt consumption and salt settings
Customer Ser-
vice
Pressure loss
Deposits in water inlet
Clean the filter
Customer Ser-
vice
Deposits in base exchanger
Clean valve and resin board
Customer Ser-
vice
Too much water in
the salt tank
Rinsing aperture is blocked
Clean rinsing aperture
Customer Ser-
vice
Injector is blocked
Clean injector and filter
Customer Ser-
vice
Foreign particles in the solenoid valve
Clean the solenoid valve, change the valve seat
Customer Ser-
vice
Power failure while filling brine
Check power source
Customer Ser-
vice
Brine is not getting
sucked in
Water inlet pressure is too low
Increase water pressure to at least 0.3 MPa (3 bar). Operator
Rinsing aperture is blocked
Clean rinsing aperture
Customer Ser-
vice
Injector is blocked
Clean injector and filter
Customer Ser-
vice
Leak inside the valve
Replace valve flaps
Customer Ser-
vice
There is always wa-
ter in the drainage,
even after regener-
ation
Valve does not execute the correct cycles
Check timer programme; replace the valve controls,
if required
Customer Ser-
vice
Foreign particle in the valve
Remove the valve control, take out the foreign parti-
cle, check valve in all the positions
Customer Ser-
vice
RO Pump does not
start
Buffer tank for permeate is full
Wait until the permeate is consumed.
Operator
Level sensor "Buffer container full" defective
Check level switch.
Customer Ser-
vice
Start-up time of the control has not yet been
completed
Wait.
Operator
Pressure switch for water scarcity is defective Check pressure switch; replace it, if required.
Customer Ser-
vice
No softened water is coming from the base ex-
changer
Check the base exchanger.
Operator/Cus-
tomer Service
Regeneration of the base exchanger is incom-
plete
Add salt, add water and wait for brine formation (ap-
prox. 2 hours); start regeneration, check the base
exchanger, if required.
Operator/Cus-
tomer Service
RO pump continu-
ously goes on and
off
Fine filter or active carbon filter dirty
Check filter; replace the filter inlay, if required
Operator
RO pump starts
only after several
rinsing cycles
Too low mains water pressure
Check mains water supply; open the inlet valve fully,
if required.
Operator
Fine filter or active carbon filter dirty
Check filter; replace the filter inlay, if required
Customer Ser-
vice
70
EN
Summary of Contents for SB MU
