Kärcher SB MU, Original Instructions Manual

Page: 62 / 276

-
25
Faults shown in the display
Display Cause Remedy
F 001 Electronic outlets overloaded Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 004 Dimming sensor defective Call customer service.
F 005 Protective motor switch on high pressure pumps was triggered Reset motor protection switch; call Customer Ser-
vice if the problem recurs.
F 006 Connection to RDS defective Call customer service.
F 007 The pressure switch air does not report any pressure Check the compressor and the compressed air
lines.
F 010 No connection to pump electronics at washing station 1 Call customer service.
F 011 Electronic outlets at washing station 1 overloaded Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 012 Current pickup of high pressure pump at washing station 1 too high
F 013 Current pickup of high pressure pump at washing station 1 too low See "Faults on high pressure pumps"
F 014 Contact of high pressure pump at washing station 1 stuck Call customer service.
F 015 Semiload valve at washing station 1 defective
F 016 Coiling protection contact of high pressure pump washing station 1 has
triggered. Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 017 Oil level of high pressure pump at washing station 1 too low Refill oil, acknowledge the fault.
F 018 Electronics at washing station 1 defective Call customer service.
F 020 No connection to remote control electronics at washing station 1 Check the connector of the data cable with the elec-
tronics of the remote control.
F 021 Fault at coin acceptor at washing station 1 Call customer service.
F 022 Check the microswitch on the mechanical coin ac-
ceptor, replace electronic coin acceptor
F 030 No connection to pump electronics at washing station 2 Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 031 Electronic outlets at washing station 2 overloaded
F 032 Current pickup of high pressure pump at washing station 2 too high Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 033 Current pickup of high pressure pump at washing station 2 too low See "Faults on high pressure pumps"
F 034 Contact of high pressure pump at washing station 2 stuck Call customer service.
F 035 Semiload valve at washing station 2 defective
F 036 Coiling protection contact of high pressure pump washing station 2 has
triggered. Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 037 Oil level of high pressure pump at washing station 2 too low Refill oil, acknowledge the fault.
F 038 Electronics at washing station 2 defective Call customer service.
F 040 No connection to remote control electronics at washing station 2 Check the connector of the data cable with the elec-
tronics of the remote control.
F 041 Fault at coin acceptor at washing station 2 Call customer service.
F 042 Check the microswitch on the mechanical coin ac-
ceptor, replace electronic coin acceptor
F 050 No connection to pump electronics at washing station 3 Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 051 Electronic outlets at washing station 3 overloaded
F 052 Current pickup of high pressure pump at washing station 3 too high Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 053 Current pickup of high pressure pump at washing station 3 too low See "Faults on high pressure pumps"
F 054 Contact of high pressure pump at washing station 3 stuck Call customer service.
F 055 Semiload valve at washing station 3 defective
F 056 Coiling protection contact of high pressure pump washing station 3 has
triggered. Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 057 Oil level of high pressure pump at washing station 3 too low Refill oil, acknowledge the fault.
F 058 Electronics at washing station 3 defective Call customer service.
F 060 No connection to remote control electronics at washing station 3 Check the connector of the data cable with the elec-
tronics of the remote control.
F 061 Fault at coin acceptor at washing station 3 Call customer service.
F 062 Check the microswitch on the mechanical coin ac-
ceptor, replace electronic coin acceptor
F 070 No connection to pump electronics at washing station 4 Acknowledge the fault. If the fault recurs, call cus-
tomer service.
F 071 Electronic outlets at washing station 4 overloaded
F 072 Current pickup of high pressure pump at washing station 4 too high Acknowledge the fault. If the fault recurs, call cus-
tomer service.
62 EN