Kantech KT-NCC Quick Configuration Manual Download Page 33 | Manualshive

Page: 33 / 40

background image

Telephone: 1 (450) 444-2030

•

Toll free: 1 (888) 222-1560

•

Fax: 1 (450) 444-2029

•

Internet: www.kantech.com



2006 Tyco Safety Products, Canada, Ltd. All rights reserved

•

Specifications may change without notice

page 32 of 39

DN1656

-

0606

WAN Network

The following diagram shows a type of architecture in a WAN network when the site of the EntraPass Server
is distant from the site of the KT-NCC module and the two communicate through a public network.

Figure 9: WAN Configuration Diagram

«
...
31
32
33
34
35
...
»

Summary of Contents for KT-NCC









































Reviews:

No comments

Related manuals for KT-NCC

Brand: FAAC Pages: 14

Brand: Garmin Pages: 12

Brand: Waters Pages: 55

Brand: Paradox Pages: 2

Brand: Abus Pages: 12

Max Charge MC-624

Brand: Balmar Pages: 8

MAX CHARGE MC-614

Brand: Balmar Pages: 20

Brand: Camozzi Pages: 33

Brand: Camozzi Pages: 2

Brand: Camozzi Pages: 64

Brand: Salda Pages: 16

Brand: Harsco Industrial Pages: 57

Brand: tams elektronik Pages: 12

Brand: Rachio Pages: 2

Brand: National Instruments Pages: 2

Brand: Uniden Pages: 28

Brand: UniFocus Pages: 23

Brand: UniFocus Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands