manualshive.com logo in svg

Kantech KT-NCC, Quick Configuration Manual, Page: 2 / 40

Share
Download
Kantech KT-NCC Quick Configuration Manual Download Page 2

Telephone: 1 (450) 444-2030 

•

 Toll free: 1 (888) 222-1560 

•

 Fax: 1 (450) 444-2029 

•

 Internet: www.kantech.com

2006 Tyco Safety Products, Canada, Ltd. All rights reserved 

•

 Specifications may change without notice

page 1 of 39

DN1656

-

0606

Purpose of this Document

This Quick Setup Guide is intended for users who are already familiar with Kantech products and have some 
knowledge of network configuration.
This document is aimed at describing the configuration steps required to establish communication between 
EntraPass Global Edition and one or several KT-NCC communication controllers, taking into account your 
environment and your network architecture.
Note that this document does not replace the reference guide that came with the KT-NCC communication 
controller and the EntraPass Global Edition software.

Reference Documents

The following documents are reference documents for EntraPass Global Edition and the KT-NCC 
communications controller:

•

KT-NCC Network communication controller, Installation Manual,

 DN1611.

•

EntraPass Global Edition

 Reference Manual DN1316.

•

How to Migrate to the KT-NCC

 DN1661.

Summary of Contents for KT-NCC









































Reviews:

No comments