Kantech KT-NCC Quick Configuration Manual Download Page 31 | Manualshive

Page: 31 / 40

background image

Telephone: 1 (450) 444-2030

•

Toll free: 1 (888) 222-1560

•

Fax: 1 (450) 444-2029

•

Internet: www.kantech.com



2006 Tyco Safety Products, Canada, Ltd. All rights reserved

•

Specifications may change without notice

page 30 of 39

DN1656

-

0606

At this stage, the system checks if the version number of the software and controller are the same. If not, the
system updates the KT-NCC firmware automatically. Three messages will appear on the list of messages of
the EntraPass workstation to indicate that the update has been completed.

The messages to lookout for are:

•

KT-NCC Update of platform CE - KT-NCC, Started

•

KT-NCC Update of platform CE - KT-NCC, Completed

•

KT-NCC Update of platform CE - KT-NCC, Successfully completed.

«
...
29
30
31
32
33
...
»

Summary of Contents for KT-NCC









































Reviews:

No comments

Related manuals for KT-NCC

Brand: Wavetec Pages: 17

Brand: Calsense Pages: 9

Smart Controller

Brand: MaestroHome Pages: 10

Brand: Ickle Bubba Pages: 23

SolarCell Remote

Brand: Samsung Pages: 2

Brand: Samsung Pages: 20

Brand: Magnescale Pages: 132

Brand: Canarm Pages: 3

Brand: Kasco Pages: 3

Brand: C Prox Ltd Pages: 5

Brand: Datalogic Pages: 15

Brand: Rane Pages: 2

Brand: RadioMaster Pages: 10

Brand: Xblue Networks Pages: 2

Brand: +GF+ Pages: 3

Brand: Össur Pages: 58

Brand: M-system Pages: 3

S3500 Series Uplink Module

Brand: Aruba Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands