Kantech KT-NCC Quick Configuration Manual Download Page 30

Page: 30 / 40

Telephone: 1 (450) 444-2030

•

Toll free: 1 (888) 222-1560

•

Fax: 1 (450) 444-2029

•

Internet: www.kantech.com



•

Specifications may change without notice

page 29 of 39

DN1656

0606

Select the

Ethernet Port #1

tab.

•

Enter the

MAC Address

of the KT-NCC. (No. 1 in the diagram on page 32).

•

Check the box

Ethernet port #1

•

Select the option

Obtain an IP Address Automatically

•

Port

18710

is automatically assigned to the KT-NCC by default. It is advisable not to modify it.

•

The box

Enable broadcast assignation

is selected by default. Leave this option as is.

•

Select the appropriate

Communication timings

. (Consult Table 2 on page 11).

Click the save icon and close the Gateway dialog. The section

Use the Following IP Address

will be

refreshed to include the KT-NCC parameters.

Close the Gateway dialog.

Summary of Contents for KT-NCC









































Search results

Summary of Contents for KT-NCC

Reviews:

Related manuals for KT-NCC

Brands by name

Popular brands

Kantech KT-NCC, Quick Configuration Manual

Search results

Summary of Contents for KT-NCC

Reviews:

Related manuals for KT-NCC

Brands by name

Popular brands