Juniper JUNOSE 11.2 Configuration Manual Download | Manualshive

Page: 544 / 772

background image

•

A combination of RADIUS authentication and profiles

You create and configure each layer of a

static interface

manually through an existing

configuration mechanism such as the command-line interface (CLI) or Simple Network
Management Protocol (SNMP).

Unlike static interfaces, dynamic interfaces are not restored through nonvolatile storage
(NVS) after a reboot.

Autodetection

The router performs

autodetection,

also referred to as

autosensing,

to determine the

layers of each dynamic interface. The autodetection process occurs when the router
conditionally constructs interface layers based on the encapsulation type of the incoming
packet.

Autodetection only uses system resources on demand based on what is detected in the
incoming packet. Dynamic interfaces are created as a result of traffic on the interface.
Dynamic interfaces can also be dynamically deleted without your intervention, thereby
enabling any consumed system resources to be returned.

Unlike dynamic interfaces, static interfaces always allocate system resources upon
creation, and always consume system resources, even when the interface is quiescent.

Types of Dynamic Interfaces

There are two types of dynamic interfaces: upper-layer and bulk-configured.
Bulk-configured dynamic interfaces enable you to dynamically create ATM 1483
subinterfaces and VLAN subinterfaces by bulk-configuring a range of identifiers. There
are two types of bulk-configured dynamic interfaces:

•

ATM 1483 interfaces over static ATM AAL5 interface

•

VLAN subinterface over static VLAN major interface

For more information, see “Configuring Dynamic Interfaces Using Bulk Configuration” on
page 619.

Upper-layer dynamic interfaces enable you to dynamically create the following
configurations:

•

Dynamic IP, PPPoE, PPP, MLPPP, and bridged Ethernet interfaces over a static ATM 1483
interface

•

IP or PPPoE interfaces over VLAN interfaces and Ethernet, Gigabit Ethernet, and
10-Gigabit-Ethernet interfaces.

NOTE:

Ethernet interfaces in this chapter refer to any of these interfaces Fast Ethernet,

Gigabit Ethernet, or 10–Gigabit-Ethernet.

Copyright © 2010, Juniper Networks, Inc.

512

JunosE 11.2.x Link Layer Configuration Guide

«
...
542
543
544
545
546
...
»

Summary of Contents for JUNOSE 11.2





































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JUNOSE 11.2

Brand: Panasonic Pages: 20

Brand: UMAX Technologies Pages: 10

Wide Format 6030

Brand: Xerox Pages: 8

PM1D Manager V2

Brand: Yamaha Pages: 24

Brand: M-Audio Pages: 5

Brand: National Instruments Pages: 86

VIRUSSCAN ENTERPRISE

Brand: McAfee Pages: 2

D-NE329SP - Atrac Cd Walkman Portable Player

Brand: Sony Pages: 2

D-NE20 - Atrac Cd Walkman

Brand: Sony Pages: 2

D-NE326CK - Atrac Cd Walkman Portable Player

Brand: Sony Pages: 2

D-NE329SP - Atrac Cd Walkman Portable Player

Brand: Sony Pages: 32

D-NE1 - Portable Cd Player

Brand: Sony Pages: 34

D-NE326CK - Atrac Cd Walkman Portable Player

Brand: Sony Pages: 35

D-NE1 - Portable Cd Player

Brand: Sony Pages: 116

Brand: AMX Pages: 34

SpeedUpMyPC 2010

Brand: UNIBLUE Pages: 11

Brand: Bacharach Pages: 12

VIAVOICE-SIMPLY DICTATION FOR MAC OS X

Brand: IBM Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands