manualshive.com logo in svg

Juniper JUNOSE 11.2.X BGP AND MPLS, Configuration Manual

Discover all the necessary information to set up and configure BGP and MPLS on your Juniper JUNOSE 11.2.X device with our free Configuration Manual. Download the manual from manualshive.com and unleash the full potential of your network infrastructure.

Share
Download
background image

Connecting IPv6 Islands Across IPv4 Clouds with BGP

If you have not upgraded your core to IPv6, you can still provide IPv6 services to customers
by connecting remote IPv6 islands across IPv4 clouds by means of MP-BGP and MPLS.
An IPv6 island is a network employing IPv6 addressing, such as a customer site. The IPv4
cloud consists of the PE–P–PE core.

NOTE:

You must configure an IPv6 interface in the parent VR for this feature to work.

Consider Figure 110 on page 476. Each customer site is connected by means of a CE router
to a PE router. The PE routers in this implementation are referred to as dual-stack BGP
(DS-BGP) routers because they run both the IPv6 and IPv4 protocol stack.

Figure 110: IPv6 Tunneled over MPLS-IPv4

The PE routers learn IPv6 routes using MP-BGP over TCPv4 or TCPv6 from the CE devices.
Alternatively, you can configure IPv6 static routes on the PE routers to reach the customer
IPv6 networks through the CE IPv6 link. You can use any IPv6-enabled routing protocol
to access the CE routers.

Use any MPLS signaling protocol to establish an MPLS base tunnel in the IPv4 core
network. Each PE router runs MP-BGP over an IPv4 stack (MP-BGP/TCP/IPv4). MP-BGP
advertises the customer IPv6 routes by exchanging IPv6 NLRI reachability information
across the IPv4 cloud.

Each PE router announces the IPv4 address of its core-facing interface (the tunnel
endpoint) to its PE peers as the BGP next hop. Because MP-BGP requires the next hop
to be in the same address family as the NLRI, the IPv4 next-hop address must be
embedded in an IPv6 format. The PE router advertises the IPv6 routes as labeled routes
and an IPv6 next hop.

In the topology shown in Figure 110 on page 476, OSPF advertises reachability of the
loopback (10.1.1.1/32 and 10.2.2.1/32) and core-facing (10.10.10.1/32 and 10.20.20.2/32)
interfaces of the PE routers. LDP binds label L1 to 10.1.1.1/32 on the P router.

Router CE 1 establishes an MP-BGP session over TCPv4 to PE 1 and advertises its ability
to reach the IPv6 network 2001:0430::/32. The MP-BGP update message specifies an

Copyright © 2010, Juniper Networks, Inc.

476

JunosE 11.2.x BGP and MPLS Configuration Guide

Summary of Contents for JUNOSE 11.2.X BGP AND MPLS







































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JUNOSE 11.2.X BGP AND MPLS

Xerox 850DP - Phaser Color Solid Ink Printer Installation Instructions preview
850DP - Phaser Color Solid Ink Printer
Brand: Xerox Pages: 2
AMX Content Database Editor v 1.0 Manual preview
Content Database Editor v 1.0
Brand: AMX Pages: 28
Siemens Simotion A4027118-A0414 User Manual preview
Simotion A4027118-A0414
Brand: Siemens Pages: 107
Siemens Gigaset talk & surf 6.0 Operating Instructions Manual preview
Gigaset talk & surf 6.0
Brand: Siemens Pages: 188
LinPlug MorphoX User Manual preview
MorphoX
Brand: LinPlug Pages: 46
Online Media Technologies AVS DVD Copy Manual preview
AVS DVD Copy
Brand: Online Media Technologies Pages: 46
Mackie FINAL MIX VST - FOR TRACKTION Manual preview
FINAL MIX VST - FOR TRACKTION
Brand: Mackie Pages: 26
Microtek ScanMaker X6 EPP User Manual preview
ScanMaker X6 EPP
Brand: Microtek Pages: 15
Microtek ScanPotter Reference Manual preview
ScanPotter
Brand: Microtek Pages: 36
FARONICS ANTI-EXECUTABLE - PRODUCT Product Data Sheet preview
ANTI-EXECUTABLE - PRODUCT
Brand: FARONICS Pages: 2
Xerox PAGIS PRO 2.0 User Manual preview
PAGIS PRO 2.0
Brand: Xerox Pages: 267
Waves Plug-in for Vocals and Monophonic User Manual preview
Plug-in for Vocals and Monophonic
Brand: Waves Pages: 20
ACRONIS BACKUP AND RECOVERY 10 - DEDUPLICATION Datasheet preview
BACKUP AND RECOVERY 10 - DEDUPLICATION
Brand: ACRONIS Pages: 2
KAPERSKY ANTI-SPAM 3.0 - Administrator'S Manual preview
ANTI-SPAM 3.0 -
Brand: KAPERSKY Pages: 153
Sharp AR-PB2 Operation Manual preview
AR-PB2
Brand: Sharp Pages: 60
Sharp e-Copy ShareScan Installation & Setup Instructions Manual preview
e-Copy ShareScan
Brand: Sharp Pages: 38
Sharp CE-LK1P Operation Manual preview
CE-LK1P
Brand: Sharp Pages: 48
Casio Mail Setup Manager User Manual preview
Mail Setup Manager
Brand: Casio Pages: 6

Brands by name

Popular brands

Load more brands