Invacare HomeFillII AW Service Manual Download Page 72

Page: 72 / 104

SECTION 10—COMPRESSOR REPLACEMENT

HomeFill

II AW Compressor

Part No 1154316

23. Remove the six mounting screws that secure the compressor/motor assembly to the

base (FIGURE 10.11).

24. Remove the compressor/motor assembly from the base.

FIGURE 10.11

Compressor Replacement - HomeFill Units Manufactured After 8/1/05

25. Carefully place the pump assembly upside down on the table.

26. Remove the timing belt by gently pulling the belt away from the large pulley and

motor pulley. Refer to Detail “A” in FIGURE 10.12.

27. Rotate pump assembly 180° so that the motor is facing up.

28. Remove the two mounting screws, two bushings, and two washers that secure the

motor to the pump assembly. Refer to Detail “B” and “C” in FIGURE 10.12.

29. Remove the motor from the pump assembly.

NOTE: Retain the two mounting screws, two bushings, and two washers for reassembly.

30. Remove the mounting screw and washer (Detail “A”) that secure the large pulley to

the pump assembly crankshaft. Refer to FIGURE 10.12 on page 73.

TOP VIEW WITH CONTROL PANEL ASSEMBLY REMOVED

Mounting Screws

Mounting

Screws

Mounting

Screws

Motor/Pump Assembly

Base

Summary of Contents for HomeFillII AW









































































































Search results

Summary of Contents for HomeFillII AW

Reviews:

Related manuals for HomeFillII AW

Brands by name

Popular brands

Invacare HomeFillII AW, Service Manual

Search results

Summary of Contents for HomeFillII AW

Reviews:

Related manuals for HomeFillII AW

Brands by name

Popular brands