Invacare HomeFillII AW Service Manual Download Page 95

Page: 95 / 104

SECTION 14—MAINTENANCE

Part No 1154316

HomeFill

II AW Compressor

Cleaning/Replacing the Cabinet Filter

WARNING

- Push the power switch to the Off (O) position and unplug the compressor before

cleaning.

DO NOT operate the compressor without the filter

installed.

CAUTION

- DO NOT unplug by pulling on cord. To unplug, grasp the plug not the cord,

otherwise damage may occur.

NOTE: For this procedure, refer to FIGURE 14.1.

NOTE: All compressors have one filter on the back of the cabinet.

NOTE: Perform this procedure at least once a week.

1. Unplug the compressor. Grasp the plug, not the cord.

2. Remove the filter.

3. Clean the filter with a vacuum cleaner or wash in warm soapy water and rinse

thoroughly.

4. Dry the filter thoroughly before reinstallation.

FIGURE 14.1

Cleaning/Replacing the Cabinet Filter

Cleaning Cabinet

DANGER

Risk Of Electric Shock

This unit contains moving and high pressure components. There are no user

serviceable parts inside the cover. To avoid electric shock, injury or death:
- DO NOT remove the cover.
- Refer servicing to qualified personnel.

1. Clean the cabinet with a mild household cleaner and non-abrasive cloth or sponge.

Cabinet Filter

Summary of Contents for HomeFillII AW









































































































Search results

Summary of Contents for HomeFillII AW

Reviews:

Related manuals for HomeFillII AW

Brands by name

Popular brands

Invacare HomeFillII AW, Service Manual

Search results

Summary of Contents for HomeFillII AW

Reviews:

Related manuals for HomeFillII AW

Brands by name

Popular brands