Invacare HomeFillII AW Service Manual Download Page 56

Page: 56 / 104

SECTION 9—MOTOR REPLACEMENT

HomeFill

II AW Compressor

Part No 1154316

23. Remove the six mounting screws that secure the pump/motor assembly to the base

(FIGURE 9.5).

FIGURE 9.5

Motor Replacement

24. Carefully place the pump assembly upside down on the table.

25. Remove the timing belt by gently pulling the belt away from the large pulley and

motor pulley. Refer to Detail “A” in FIGURE 9.6.

26. Rotate pump assembly 180° so that the motor is facing up.

27. Remove the two mounting screws, two bushings, and two washers that secure the

motor to the pump assembly. Refer to Detail “B” and “C” in FIGURE 9.6.

28. Remove the motor from the pump assembly.

NOTE: Retain the two mounting screws, two bushings, and two washers for reassembly.

TOP VIEW WITH CONTROL PANEL ASSEMBLY REMOVED

Mounting Screws

Mounting

Screws

Mounting

Screws

Motor/Pump Assembly

Base

Summary of Contents for HomeFillII AW









































































































Search results

Summary of Contents for HomeFillII AW

Reviews:

Related manuals for HomeFillII AW

Brands by name

Popular brands

Invacare HomeFillII AW, Service Manual

Search results

Summary of Contents for HomeFillII AW

Reviews:

Related manuals for HomeFillII AW

Brands by name

Popular brands