Invacare HomeFillII AW Service Manual Download Page 73

Page: 73 / 104

SECTION 10—COMPRESSOR REPLACEMENT

Part No 1154316

HomeFill

II AW Compressor

31. Remove the large pulley from the pump assembly crankshaft.

FIGURE 10.12

Compressor Replacement - HomeFill Units Manufactured After 8/1/05

Reassembly of HomeFill Units

NOTE: For this procedure, refer to FIGURE 10.7 through FIGURE 10.12.

1. Position the washers on the new pump assembly. Refer to Detail “C” in FIGURE 10.12.

2. Position the motor on the new pump assembly. Refer to Detail “B” in FIGURE 10.12.

3. Press the large pulley onto the new pump assembly crankshaft. Refer to Detail “A”

FIGURE 10.12 on page 73.

DETAIL “A”

Pump Assembly

DETAIL “B”

DETAIL “C”

Washers

Timing

Belt

Large Pulley

Motor Pulley

Pump

Assembly

Mounting Screw

and Washer

Pump Assembly

Crankshaft

Mounting

Screw

Bushing

Mounting

Screw

Bushing

Motor

Pump

Assembly

Summary of Contents for HomeFillII AW









































































































Search results

Summary of Contents for HomeFillII AW

Reviews:

Related manuals for HomeFillII AW

Brands by name

Popular brands

Invacare HomeFillII AW, Service Manual

Search results

Summary of Contents for HomeFillII AW

Reviews:

Related manuals for HomeFillII AW

Brands by name

Popular brands