Inficon Sensistor Sentrac Service Instructions Manual Download Page 24 | Manualshive

Page: 24 / 76

background image

4 | Troubleshooting

INFICON

24 / 76

Sensistor Sentrac-Leak Detector-ServiceManual-nip65en1-05-(1901)

Message

Indicators

Technical

Description

Cause of Warning

Measure

Error Code

Probe Software

not compatible

with the

instrument.

Change probe

or upgrade

probe software.

Red measure

window present

on screen, Blue

LED flashing.

The instrument

software is not

compatible with

the probe

software.

Probe Software

not compatible

with the

instrument.

Change probe or

upgrade the probe

software.

06

Two probes

connected.

Disconnect one

probe and

restart the

instrument.

Red measure

window present

on screen, Blue

LED flashing.

Software can not

handle two

probes.

Two probes

connected to the

instrument.

Disconnect one

probe and restart

the instrument.

07

Instrument

hardware error,

service

recommended.

Red measure

window present

on screen, Blue

LED flashing.

Instrument PCB

broken.

Instrument PCB

broken.

Change Main

PCB.

08

Probe hardware

error, service

recommended.

Red measure

window present

on screen, Blue

LED flashing.

Probe PCB

broken.

Probe PCB

broken.

Change Probe

PCB.

09

«
...
22
23
24
25
26
...
»

Summary of Contents for Sensistor Sentrac













































































Reviews:

No comments

Related manuals for Sensistor Sentrac

Brand: OCO Pages: 11

Brand: D-Link Pages: 8

Brand: Dash Pages: 2

Brand: olympia electronics Pages: 2

Brand: GBO Technology Pages: 103

CarSense202 CS202

Brand: EMX Industries Pages: 5

Brand: Qvis Pages: 32

Brand: Raytec Pages: 11

Brand: Bose Sicilia Pages: 24

Brand: ERNITEC Pages: 2

Brand: ZKTeco Pages: 55

Brand: Eneo Pages: 90

Brand: Abus Pages: 124

Brand: Polaroid Pages: 73

NVIP-3DN7000V/IRH-2P

Brand: Novus Pages: 24

EsiWelma Sensigas URS20SS

Brand: Navim Group Company Pages: 8

Brand: Atomic Beam Pages: 2

Brand: Love Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands