Inficon Sensistor Sentrac Service Instructions Manual Download Page 46

Page: 46 / 76

5 | Service Instructions

INFICON

46 / 76

Sensistor Sentrac-Leak Detector-ServiceManual-nip65en1-05-(1901)

5.11 Changing Speaker

Part

Part no.

Qty

Consumables

KB1114 Speaker

591-826

WARNING

Electrical hazard!

When function test is performed on an open instrument, there is a risk of electrical

shock.

CAUTION

Caution

Be very cautious when removing the locking on connector J2 (FFC cable, LCD data,

on main PCB). See Drawings [

}

71].

Disassemble

Disconnect the mains connector.

Remove the cover, see Disassemble in Remove the Cover [

}

28].

Remove the four screws (A) holding the Front Panel (B).

Remove all cables between the Front Panel (B) and the PCB. Pay special

attention to J2. Carefully tap the screwdriver / locking alternately left/right to

loosen the cable from the connector. Do not use force!

Remove the Front Panel.

Remove the four screws (C) holding the Speaker (D).

Summary of Contents for Sensistor Sentrac













































































Search results

Summary of Contents for Sensistor Sentrac

Reviews:

Related manuals for Sensistor Sentrac

Brands by name

Popular brands

Inficon Sensistor Sentrac, Service Instructions Manual

Search results

Summary of Contents for Sensistor Sentrac

Reviews:

Related manuals for Sensistor Sentrac

Brands by name

Popular brands