Inficon Sensistor Sentrac Service Instructions Manual Download Page 7

Page: 7 / 76

INFICON

General Information | 2

Sensistor Sentrac-Leak Detector-ServiceManual-nip65en1-05-(1901)

7 / 76

2 General Information

Read this Manual carefully before putting your instrument into service. When reading,

pay particular attention to the WARNINGS, CAUTIONS and NOTICES found

throughout the text.

2.1 About this Document

This document is only intended for INFICON service personnel working with the

Sensistor Sentrac Leak Detector.

2.2 Document History

Revision

Date

Remark

03-2015

First public release

12-2016

Second public release

06-2018

Third public release

01-2019

Fourth public release

2.3 Versions

This manual applies to the product versions below.

Unit

Name

Software Version

Leak Detector

Sensistor Sentrac

1.01.01 or higher

Hand Probe

P60

1.01.01 or higher

For more information about the latest software versions, please contact your local

INFICON office.

2.4 Password

The service password is: 4711 (the old password 7367 is still working).

This password is not intended for end users and should not be re-distributed.

Summary of Contents for Sensistor Sentrac













































































Search results

Summary of Contents for Sensistor Sentrac

Reviews:

Related manuals for Sensistor Sentrac

Brands by name

Popular brands

Inficon Sensistor Sentrac, Service Instructions Manual

Search results

Summary of Contents for Sensistor Sentrac

Reviews:

Related manuals for Sensistor Sentrac

Brands by name

Popular brands