Ikegami FA-97, Operation Manual

Page: 107 / 156

5.2 Settings from the Menu
HDK-97C 1303 VER1 (U)
91
C
A
ME
R
A
SE
T
T
INGS an
d AD
JUS
T
ME
NT
5
Menu Item Initial Setting Setting Value De s cription, Remark s
MENU DATA
ALL VF
CUSTOM GAMMMA MODE
EASY MODE
Easy creation mode. Sets various parameters and creates the
custom gamma data.
DEFAULT RESET
--- EXECUTE, CANCEL
Returns to the original custom gamma data.
If you have saved the custom gamma data with the "SAVE"
function, it returns to the saved data.
The original data cannot be recovered once it is overwritten
with the "SAVE" function.
- -
SELECT
NORMAL
NORMAL, CINE1-2,
CUSTOM1-5
Selects the gamma table to be created. - -
CURVE TYPE
---
NORMAL, LOG,
SPECIAL
Sets the basic properties of gamma curve. - *4 -
INITIAL GAIN
--- 1.0 - 9.0
Sets the slope of gamma curve at around 0%.
The curve rises steeply as the value increases.
-
*4
-
18% GRAY
--- 14.0% - 107.0%
Sets what level it should be after the gamma has been applied
when converting from 18% level before applied.
-
*4
-
DYNAMIC RANGE
--- 100% - 600%
Sets the maximum level (the maximum input level to the
gamma) before the gamma has been applied.
-
*4
-
WHITE LIMIT
--- 70% - 109% Sets the white clip after the gamma has been applied. -
*4
-
CAL
OFF
OFF, CAL100%,
CAL200%, CAL300%,
CAL400%, CAL600%
Selects the test waveform (CAL) to check the gamma table. - -
SAVE
---
EXECUTE,
CANCEL
Saves the data that has been created.
The data is temporary unless you save it.
Therefore, the data will be cleared if you end the menu without
saving it.
- -
FLEXIBLE MODE
Flexible creation mode. Edits the already created custom
gamma data.
DEFAULT RESET
READY CANCEL, EXECUTE Returns to the original custom gamma data. - -
SELECT
NORMAL NORMAL,CUSTOM1 to 5 Selects the gamma table to be created. - -
POINT
100% 15 to 440% Sets the video level before the gamma has been applied. - -
WIDTH
60% 20 to 100% Sets the width of the video level . - -
LEVEL
0 -100 to 100
Sets the video level of the range set by the WIDTH and
POINT.
- -
CAL
OFF
OFF, CAL100%,CAL200%
,CAL300%,CAL400%,CA
L600%
Sets the test waveform to verify gamma table. - -
SHUTTER
OFF OFF, PRESET, VARIABLE Selects for the electronic shutter. - -
SHUTTER SPEED
1/100
PRESET:
1/100 - 1/2000
VARIABLE:
1/63.4 - 1/1983
Switches the shutter speed.
(When SHUTTER is in PRESET and VARIABLE only.)
- -
GAMMA CURVE COPY
---
CUSTOM1-5 -->
CUSTOM1-5 Copies the gamma data that has been created into the other
data in the camera.
- -
SD MEMORY CARD
- -
SAVE
--- --- Saves the custom gamma data in an SD card. - -
LOAD
--- --- Loads the custom gamma data from an SD card. - -
PRESET FILE LOAD
Function to load the user settings (ENGINEER SET FILE)
or factory settings (FACTORY SET FILE) for the level
adjustment or menu of the camera.
Used to return the camera state back to the previous or initial
settings.
FILE SELECT
ENGINEER ENGINEER, FACTORY
ENGINEER : Initializes the state back to the user setting.
FACTORY : Initializes the state back to the initial factory
setting.
- -
LOAD START
READY READY, START, CANCEL Executes initialization. - -
*4 : CUSTOM GAMMA MODE - Loads the custom gamma data from SD card through the LOAD menu.