manualshive.com logo in svg

IFM Ecomat 100 Mobile CR0301, Programming Manual

The IFM Ecomat 100 Mobile CR0301 is a cutting-edge industrial control system. Enhance your understanding and programming skills with the comprehensive Programming Manual available for free download on our website. Gain control over your operations with this manual's invaluable insights and practical instructions. Download it today from manualshive.com.

Share
Download
background image

 

 

82 

ifm

 Programming Manual 

ecomatmobile

 CabinetController (CR0301) Runtime System V05 

2016-04-21 

ifm function elements 

ifm function elements for the device CR0301 

> 

 

Parameters of the outputs 

2029 

Parameter 

Data type 

Description 

NODE_ID 

BYTE 

current node ID of the CANopen master 

BAUDRATE 

WORD 

current baudrate of the CANopen master in [kBaud] 

NODE_STATE 

INT 

Current status of CANopen master 

SYNC 

BOOL 

SYNC signal of the CANopen master 
TRUE: 

In the last cycle a SYNC signal was sent 

FALSE: 

In the last cycle no SYNC signal was sent 

RX_OVERFLOW 

BOOL 

TRUE: 

Error: receive buffer overflow 

FALSE: 

no overflow 

TX_OVERFLOW 

BOOL 

TRUE: 

Error: transmission buffer overflow 

FALSE: 

no overflow 

OD_CHANGED 

BOOL 

TRUE: 

Data in the object directory of the CANopen master  

  

have been changed 

FALSE: 

no data change 

ERROR_CONTROL 

ARRAY [0..7] OF BYTE 

The array contains the list (max. 8) of missing network nodes (guard 

or heartbeat error) 

GET_EMERGENCY 

STRUCT 

CANx_EMERGENY_MESSAG

E 

At the output the data for the structure 

CANx_EMERGENCY_MESSAGE are available. 
The last received EMCY message in the CANopen network is always 

displayed. 
To obtain a list of all occurred errors, the array 

EmergencyObjectSlavesArray must be evaluated! 

NODE_ID 

BYTE 

node ID of the master 

BAUDRATE 

WORD 

baud rate of the master 

NODE_STATE 

INT 

current status of the master 

SYNC 

BOOL 

SYNC signal of the master 

This is set in the 

tab [CAN parameters]

 of the master depending on 

the set time [Com. Cycle Period]. 

RX_OVERFLOW 

BOOL 

error flag "receive buffer overflow" 

 

 

 

Summary of Contents for Ecomat 100 Mobile CR0301






















































































































































































































Reviews:

No comments

Related manuals for Ecomat 100 Mobile CR0301

Zetkama 221 User Manual preview
221
Brand: Zetkama Pages: 6
Facility Explorer FX Series Installation Instructions preview
FX Series
Brand: Facility Explorer Pages: 4
Quickmill E61 Assembling Instructions preview
E61
Brand: Quickmill Pages: 3
ZIMO MX10 Instruction Manual preview
MX10
Brand: ZIMO Pages: 38
Manfrotto 851 Instructions Manual preview
851
Brand: Manfrotto Pages: 16
Madas M16/RM N.C. DN 65 EEX Technical Manual preview
M16/RM N.C. DN 65 EEX
Brand: Madas Pages: 44
Taco Electronic Solutions iWorx MPU2 Installation Manual preview
iWorx MPU2
Brand: Taco Electronic Solutions Pages: 28
UNICORECOMM UM4B0 User Manual preview
UM4B0
Brand: UNICORECOMM Pages: 32
UNICORECOMM UM220-IV M0 Additional Instructions For Installation And Operation preview
UM220-IV M0
Brand: UNICORECOMM Pages: 7
UNICORECOMM UM220-INS NF Installation And Operation User Manual preview
UM220-INS NF
Brand: UNICORECOMM Pages: 26
UNICORECOMM UM220-INS NF User Manual preview
UM220-INS NF
Brand: UNICORECOMM Pages: 25
YOKOGAWA UT35A-L User Manual preview
UT35A-L
Brand: YOKOGAWA Pages: 150
YOODA NANO Series Quick Start Manual preview
NANO Series
Brand: YOODA Pages: 3
YMGI 584 Series User Manual preview
584 Series
Brand: YMGI Pages: 8
Saluki SMR Series Quick Start Manual preview
SMR Series
Brand: Saluki Pages: 13
National Instruments SCXI -1122 Calibration Procedure preview
SCXI -1122
Brand: National Instruments Pages: 17
Davey Torrium 2 TT45 Installation And Operating Instructions Manual preview
Torrium 2 TT45
Brand: Davey Pages: 12
M-system R7HL-DC16B-R Instruction Manual preview
R7HL-DC16B-R
Brand: M-system Pages: 5

Brands by name

Popular brands

Load more brands