Icom IC-F62D Operating Manual Download Page 89

Page: 89 / 125

MDC 1200 SYSTEM OPERATION

8-8

Receiving a PTT ID call

When a PTT ID call is received:

•

Beeps sound, depending on the presetting�

•

May vibrate, depending on the presetting�

• The calling stationʼs ID is displayed.

ID 1

Call

Scan

Receiving an MDC Emergency call

When an MDC Emergency call is received:

•

Beeps sound�

•

Portable type transceivers may vibrate, depending

on the presetting�

• The calling stationʼs ID and “Emergency” is

alternately displayed�

Emergency

Call

Scan

ID 1

Call

Scan

Hold down [PTT] to speak�

The transceiver automatically may transmit an

acknowledgment to the calling station, depending

on the setting�

To stop the Emergency beeps, turn OFF the

transceiver, change the channel, or push [PTT] or

a key�

Receiving an MDC Selective Call

(Sel Call)

When an MDC Sel Call is received:

•

Beeps sound�

•

“ ” is displayed�

•

“

” blinks�

• The calling stationʼs ID is displayed.

ID 1

Call

Scan

Hold down [PTT] to speak�

Receiving an MDC Call Alert call

When an MDC Call Alert call is received,

•

Beeps sound�

•

“

” blinks�

• The calling stationʼs ID is displayed.

ID 1

Call

Scan

Hold down [PTT] to speak�

Receiving a call

Summary of Contents for IC-F62D






























































































































Search results

Summary of Contents for IC-F62D

Reviews:

Related manuals for IC-F62D

Brands by name

Popular brands

Icom IC-F62D, Operating Manual

Search results

Summary of Contents for IC-F62D

Reviews:

Related manuals for IC-F62D

Brands by name

Popular brands