manualshive.com logo in svg

Icom IC-F62D, Operating Manual

Share
Download
Icom IC-F62D Operating Manual Download Page 120

12

OTHERS

12-4

This section describes how to copy data from a 

Master transceiver to a Sub transceiver using the 

optional OPC-1870 

zone

 

copy

 

cable

�

NOTE: 

Before copying, set 

Transceiver Data Out 

to 

“ON” using the CS-F52D 

programming

 

software

.

(Common > Security Setting > Security)

 

D

Copying data

Step 1: Entering the Programming mode  (Master)

 While holding down [P1] and [F2], turn ON the 

transceiver. Continue holding down [P1] and [F2] for 

about 3 seconds.

 

•  “Programming” is displayed and the transceiver enters the 

Programming mode.

Step 2: Turning ON the transceiver 

(Sub)

Step 3: Copying data 

(Master)

 Push [PTT] on the Master transceiver to start copying 

data to the Sub transceiver.

Step 4: Complete 

(Master/Sub)

After copying is completed, the Master and Sub 

transceivers automatically restart.

 

•  The user can operate the Sub transceiver with the loaded 

data.

 

D

Connecting

Before copying, connect the Master and Sub 

transceivers using the optional OPC-1870.

1� 

Turn OFF the Master and Sub transceivers.

2� 

Connect the two transceivers with the cable.

OPC-1870

Turn OFF

Turn OFF

Copying data from a transceiver

Summary of Contents for IC-F62D






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands