background image

3

BASIC OPERATION

3-4

 

D

Selecting an operating channel

<Key or Rotary Encoder operation>

 

z

Rotate [Rotary Encoder]� 

 

z

Push [CH Up] or [CH Down]�

<Voting operation>

The transceiver automatically starts scanning when a 

Zone specified for the Voting operation is selected.

The Voting scan detects the signal strength of the 

repeaters, and automatically selects the strongest 

one�

<Automatic Scan operation>

Depending on the presetting, when the user turns ON 

the transceiver, a scan automatically starts. The scan 

stops when a call is received�

 

D

Selecting the Priority A or B channel

<Key operation>

 Push [Prio-A] or [Prio-B] to select the Priority A or 

Priority B channel�

<Menu operation>

(Menu > Channel/Scan > 

Priority A CH

)

(Menu > Channel/Scan > 

Priority B CH

)

1�  Push [Menu] to display the “Menu” screen.

2�   Push [P2 (Up)] or [P1 (Down)] to select “Channel/

Scan,” then push [OK]�

 Channel/Scan

 

 Signaling/Call

 

Menu

3�   Push [P2 (Up)] or [P1 (Down)] to select “Priority A 

CH” or “Priority B CH,” then push [OK]�

Priority A CH

 

Prio A (RW)

 

Channel/Scan

4�   After a dialog is displayed, as shown below, push 

[P2 (Up)] or [P1 (Down)] to select <OK> on the 

dialog and push [OK]�

R

 

Are u Sure?

Cancel

OK

Priority A CH

 •“Priority A CH” is briefly displayed and is selected as 

an operating channel�

5�   Hold down [Back] for 1 second to return to the 

standby screen�

Selecting a channel

Summary of Contents for IC-F62D






























































































































Reviews: