background image

7

NXDN™ OPERATION

7-11

 

D

Transmitting an Emergency call 

An NXDN Emergency call can be transmitted in 

the same way as the 2-Tone, 5-Tone, or MDC 1200 

signaling operation� See “Emergency call” for details� 

(pp� 4-3 ~ 4-6)

Transmitting a call

 

D

Transmitting Position data

When the GPS function is ON, and the optional 

HM-233GP 

gps

 

speaker

 

microphone

 receives 

Position data, the longitude and latitude data can be 

automatically transmitted:

 •When a GPS request status message is received�

 • After sending a voice message�

 

L

 Set  the 

Send with Login

 and 

Send with Logoff

 to 

“Enable�”

 • After sending a Status Message�

 

L

Set the 

Send with Status Call

 to “Enable�”

 • After sending a Message�

 

L

Set the 

Send with Message Call

 to “Enable�”

 • After sending a Call Alert�

 

L

Set the 

Send with Call Alert

 to “Enable�”

 • After sending an Emergency call�

 

L

Set the 

Send with Emergency

 to “Enable�”

 • At the preset interval�

 

L

Set the 

Auto

 to “Enable�”

 

L

Set the 

Interval Timer [mm:ss]

NOTE:

 To transmit position data, the settings above 

are required using the CS-F52D 

programming

 

software

.

 •(GPS > Digital)

 •( GPS > Common > Auto-Timed GPS Send)

Summary of Contents for IC-F62D






























































































































Reviews: