![background image](http://html2.mh-extra.com/html/icom/ic-7800/ic-7800_instruction-manual_4148585062.webp)
4-14
D
D
Convenient functions for receive
D
D
About RTTY reverse mode
Received characters are occasionally garbled when
the received signal has Mark and Space tones re-
versed. This reversal can be caused by incorrect TNC
connections, setting, commands, etc. To receive re-
versed RTTY signals correctly, select RTTY-R mode.
➥
During RTTY mode, push [RTTY/PSK] for 1 sec. to
select RTTY and RTTY-R mode.
D
D
Twin peak filter
The twin peak filter changes audio frequency response
by boosting the mark and space frequencies (2125 and
2295 Hz) for better reception of RTTY signals.
➥
During RTTY mode, push [APF/TPF] to turn the twin
peak filter ON and OFF.
• “
” appears in the LCD and the [APF/TPF] indicator
above this switch lights green while the filter is in use.
NOTE:
When the twin peak filter is in use, the re-
ceived audio output may increase. This is a normal,
not a malfunction.
TPF
[APF/TPF]
(SUB)
[APF/TPF]
(MAIN)
Normal
Reverse
Space
Mark
BFO
Space
Mark
BFO
170 Hz
2125 Hz
170 Hz
2125 Hz
• Preamp
(p. 5-9)
➥
Push [P.AMP] several times to set the preamp
OFF, preamp 1 ON or preamp 2 ON.
• “P.AMP1” or “P.AMP2” appears when the preamp 1 or
preamp 2 is ON. Main and sub have independent
preamp controls.
• Attenuator
(p. 5-9)
➥
Push [ATT] several times to set the attenuator in
6 dB steps.
• Pushing [ATT] for 1 sec. to set the attenuator in 3 dB
steps.
• “ATT” and attenuation level appear when the attenu-
ator is ON.
• Noise blanker
(p. 5-17)
➥
Push [NB] switch to turn the noise blanker ON
and OFF, and then rotate [NB] control to adjust
the threshold level.
• Noise blanker indicator (above [NB] switch) lights
when the noise blanker is ON.
• Push [NB] for 1 sec. to enter noise blanker set mode.
• Twin PBT (passband tuning)
(p. 5-12)
➥
Rotate [TWIN PBT] controls (inner/outer).
• Push [PBT CLEAR] to clear the settings.
• Noise reduction
(p. 5-18)
➥
Push [NR] switch to turn the noise reduction ON
and OFF.
• Rotate [NR] control to adjust the noise reduction
level.
• Noise reduction indicator (above [NR] switch) lights
when the noise reduction is ON.
• Auto notch filter
(p. 5-19)
➥
Push [NOTCH] switch to turn the manual notch
function ON and OFF.
• Rotate [NOTCH] control to set the attenuating fre-
quency.
• Notch indicator (above [NOTCH] switch) lights when
either the manual notch is ON.
• AGC (auto gain control)
(p. 5-11)
➥
Push [AGC] switch several times to select
AGC FAST, AGC MID or AGC SLOW.
➥
Push [AGC VR] to turn the AGC time constant
manual setting ON and OFF.
• Rotate [AGC] control to adjust the time constant.
•
1
⁄
4
function
(p. 3-6)
➥
Push [1/4] to turn the
1
⁄
4
function ON and OFF.
4
RECEIVE AND TRANSMIT