manualshive.com logo in svg

IBM Infoprint 6500-v05, Maintenance Manual


Share
Download
background image

Fan Assembly, Hammer Bank

332

Fan Assembly, Hammer Bank

Removal

1.

Prepare the printer for maintenance (page 313).

2.

Remove the ribbon. (Refer to the 

User’s Manual.)

3.

Remove the shuttle cover assembly (page 326).

4.

Pedestal Model: Remove the top cover assembly (page 327).

5.

Trace the hammer bank fan cable assembly back to the controller board connector J107, releasing it from all cable 
constraints. (See the cable routing diagrams on page 282 and page 283.)

6.

Disconnect connector P107 from the controller board and remove the fan connector (HBF) from the connector shell. (See 
page 324.)

7.

Remove the two screws securing the fan to the base casting. Angle the hammer bank fan assembly up and out of the base 
casting and feed the motor wires and cable connector out from between the base casting and the base pan. (See Figure 
46, page 416.)

Installation

ATTENTION

Install the fan so the label faces up. Air flow is UP.

NOTE:

The hammer bank fan assembly is installed by angling it down and under the shuttle motor.

1.

Feed the hammer bank fan cable connector (HBF) and motor wires between the fan well of the base casting and the base 
pan. Reach up under the base casting and route the fan cable to the right and angle the hammer bank fan assembly under 
the shuttle motor and down into the fan well. (See Figure 46, page 416.)

2.

Route the fan motor wires as shown on page 282 and page 283, connect fan cable connector (HBF) to P107, then connect 
P107 to J107 on the controller board. (See page 324.)

3.

Install two screws in the locations shown in Figure 46 on page 416.

4.

Pedestal Model: Install the top cover assembly (page 327).

5.

Install the shuttle cover assembly (page 326).

6.

Install the ribbon. (Refer to the 

User’s Manual.)

7.

Return the printer to normal operation (page 314).

Summary of Contents for Infoprint 6500-v05

































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Infoprint 6500-v05

G3D T-1000 Quick Start Manual preview
T-1000
Brand: G3D Pages: 4
3Doodler Flow User Manual preview
Flow
Brand: 3Doodler Pages: 8
DataCard SD260L Installation And Administrator'S Manual preview
SD260L
Brand: DataCard Pages: 130
Savin 8025e Operating Instructions Manual preview
8025e
Brand: Savin Pages: 160
Lexmark C770n Specification Sheet preview
C770n
Brand: Lexmark Pages: 2
Xerox Phaser 6700V/DX User Manual preview
Phaser 6700V/DX
Brand: Xerox Pages: 162
Xerox Phaser 6600N Specifications preview
Phaser 6600N
Brand: Xerox Pages: 4
Lexmark MX71 series Service Manual preview
MX71 series
Brand: Lexmark Pages: 807
Riso HC5500T User Manual preview
HC5500T
Brand: Riso Pages: 66
Xerox Nuvera 100 roduction Systems Paper Manual preview
Nuvera 100 roduction Systems
Brand: Xerox Pages: 70
Output Technology LaserMatrix LM2405 Operator'S Manual preview
LaserMatrix LM2405
Brand: Output Technology Pages: 249
Panasonic DP-CL21 Series Setup Manual preview
DP-CL21 Series
Brand: Panasonic Pages: 32
Panasonic DP-CL21 Series Maintenance And Specifications preview
DP-CL21 Series
Brand: Panasonic Pages: 103
OmniPrint FREEJET 330TX Official User Manual preview
FREEJET 330TX
Brand: OmniPrint Pages: 71
Roland VersaStudio BR-20 Master Manual preview
VersaStudio BR-20
Brand: Roland Pages: 112
Roland SP-300i User Manual preview
SP-300i
Brand: Roland Pages: 134
Roland CAMM-1 PNC-1610 User Manual preview
CAMM-1 PNC-1610
Brand: Roland Pages: 41
Kodak 5500 - EASYSHARE All-in-One Color Inkjet Start Here Manual preview
5500 - EASYSHARE All-in-One Color Inkjet
Brand: Kodak Pages: 32

Brands by name

Popular brands

Load more brands