manualshive.com logo in svg

IBM Infoprint 6500-v05, Maintenance Manual


Share
Download
background image

Table of Contents

5

Loading Flash Memory .................................................................................................................................................... 238

Loading Through The Serial Or Parallel Port ............................................................................................................ 239

Loading Through the Network Interface Card (NIC) ................................................................................................. 248

Reprogramming the Security Key.................................................................................................................................... 250

Shuttle Electrical Shorts Test........................................................................................................................................... 252

Hammer Bank Power Cable Shorts Test......................................................................................................................... 253

Cable Shorts Test ............................................................................................................................................................ 254

Main Wire Harness Test Diagnostic ................................................................................................................................ 256

Power Supply Operational Check.................................................................................................................................... 258

3   Locations ..................................................................................................................262

Locations Of Components And Assemblies .................................................................................................................... 262

4   Circuit Diagrams, Circuit Boards, Cables, and Switches ..........................................264

Contents .......................................................................................................................................................................... 264

5   Removals and Adjustments ......................................................................................311

About This Chapter.......................................................................................................................................................... 311

Tools And Materials .................................................................................................................................................. 311

Preparing The Printer For Maintenance .................................................................................................................... 313

Restoring The Printer To Operation .......................................................................................................................... 314

Removal And Replacement Procedures.......................................................................................................................... 315

List Of Procedures .................................................................................................................................................... 315

Belt, Paper Feed Timing ........................................................................................................................................... 317

Belt, Platen Open ...................................................................................................................................................... 318

Circuit Board: PSA3 Controller.................................................................................................................................. 319

Circuit Board: Power Supply ..................................................................................................................................... 321

Circuit Breaker .......................................................................................................................................................... 322

Connector Shells ....................................................................................................................................................... 323

Cover Assembly, Hammer Bank / Ribbon Mask ....................................................................................................... 325

Cover Assembly, Shuttle ........................................................................................................................................... 326

Summary of Contents for Infoprint 6500-v05

































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Infoprint 6500-v05

Pantum P2200 Series Maintenance Manual preview
P2200 Series
Brand: Pantum Pages: 105
Lanier LD225 Function Manual preview
LD225
Brand: Lanier Pages: 138
Lanier LD225 Fax Manual preview
LD225
Brand: Lanier Pages: 236
Xerox VersaLink B600 User Manual preview
VersaLink B600
Brand: Xerox Pages: 200
Xerox VersaLink C625 Manual preview
VersaLink C625
Brand: Xerox Pages: 14
Hanin MT800Q User Manual preview
MT800Q
Brand: Hanin Pages: 76
Oki C650/ES6450 Basic Operation Manual preview
C650/ES6450
Brand: Oki Pages: 180
Parkside PGG 15 C2 Translation Of The Original Instructions preview
PGG 15 C2
Brand: Parkside Pages: 104
Lexmark XM3250 User Manual preview
XM3250
Brand: Lexmark Pages: 289
Xerox WorkCentre 7830 Specification preview
WorkCentre 7830
Brand: Xerox Pages: 12
Riso KZ30 User Manual preview
KZ30
Brand: Riso Pages: 82
Magtek ExpressCard 500 User Manual preview
ExpressCard 500
Brand: Magtek Pages: 49
Xerox 3R11500 Specifications preview
3R11500
Brand: Xerox Pages: 2
MIMAKI OPT-J0529 Operation Manual preview
OPT-J0529
Brand: MIMAKI Pages: 30
Lexmark Optra W810 Service Manual preview
Optra W810
Brand: Lexmark Pages: 489
Boley GraverMach AT Operation And Maintenance Manual preview
GraverMach AT
Brand: Boley Pages: 20
Canon PIXMA E300 series Getting Started preview
PIXMA E300 series
Brand: Canon Pages: 28
Canon MultiPASS F60 Basic Manual preview
MultiPASS F60
Brand: Canon Pages: 115

Brands by name

Popular brands

Load more brands