manualshive.com logo in svg

IBM Infoprint 6500-v05, Maintenance Manual

Share
Download
IBM Infoprint 6500-v05 Maintenance Manual Download Page 321

Circuit Board: Power Supply

321

Circuit Board: Power Supply

ATTENTION

Do not touch components on the board during removal or installation. Lift and handle the board only by the loops 
provided for this purpose.

Removal 

1.

Prepare the printer for maintenance (page 313).

2.

Cabinet Model: Remove the paper guide assembly (page 348).
Pedestal Model: Remove the top cover assembly (page 327).

3.

Mark then disconnect all cable assemblies going to and from the power supply board. (See page 406, item 3.)

4.

Loosen—do not remove—the screws securing the power supply board to top rear wall of the card cage. (See page 406, 
item 15.)

5.

Grasp the power supply by the handling loops, tilt it forward, and lift it out of the printer.

Installation

1.

Reverse steps 2 through 5 of the removal procedure.

2.

Models 6500-v15 and -v20: adjust the coil temperature if the original power supply board was replaced by a new or 
refurbished power supply (page 383).

3.

Cabinet Model: Install the paper guide assembly (page 348).
Pedestal Model: Install the top cover assembly (page 327).

4.

Return the printer to normal operation (page 314).

<4>

To prevent injury from electric shock, wait at least one minute after powering off before removing the 
power supply board.

CAUTION

Summary of Contents for Infoprint 6500-v05

































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands