manualshive.com logo in svg

IBM Infoprint 6500-v05, Maintenance Manual

Share
Download
IBM Infoprint 6500-v05 Maintenance Manual Download Page 358

RibbonMinder** Sensor

358

RibbonMinder** Sensor

Removal

1.

Prepare the printer for maintenance (page 313).

2.

Cabinet Model: Remove the paper guide assembly (page 348).
Pedestal Model: Remove the top cover assembly (page 327).

3.

Remove the screw securing the RibbonMinder sensor to the base casting. (See page 413, Figure 45, items 28 and 29.)

4.

Trace the sensor cable back to the controller board, noting the cable routing and releasing the cable from restraints as 
necessary.

5.

Disconnect the RibbonMinder sensor cable connector from J122 on the controller board.

6.

Lift the sensor and guide the sensor cable up and out of the base casting.

Installation

1.

Reverse steps 2 through 6 of the removal procedure above.

2.

Return the printer to normal operation (page 147).

Summary of Contents for Infoprint 6500-v05

































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands