manualshive.com logo in svg

IBM Infoprint 6500-v05, Maintenance Manual

Share
Download
IBM Infoprint 6500-v05 Maintenance Manual Download Page 149

Display Messages

149

B54 ERROR: SDA
LINE STUCK LOW

The serial data signal has shorted 
low on the controller board.

1.

Cycle power. If the message appears, replace the controller 
board (page 319). After replacing the controller board, DO NOT 
make the printer READY, but proceed immediately to the next 
step.

2.

Download and install the latest code from IBM First (page 231).

3.

Power on the printer in download mode, and load flash memory 
(page 238).

4.

If you encounter the failure after replacing the controller board, 
reinstall the original controller board and contact your DDS and 
Second Level Support.

B55 SEND PROGRAM
TO EC

Status message: the printer is 
loading the engine controller 
program into the engine controller.

No action required.

BOOT DIAGNOSTICS

Non-error status message.

No action required.

CLEARING PROGRAM
FROM FLASH

Status message: emulation 
software successfully loaded into 
printer RAM and the checksum 
matched. The old program is now 
being deleted from flash memory.

No action required.

DIAGNOSTIC PASSED

Status message: the printer 
passed its memory and hardware 
initialization tests.

No action required.

DO NOT POWER OFF
DOWNLOADING XX%

Status message: the printer is 
downloading emulation software 
into RAM. XX% indicates the 
percentage of program that has 
been loaded. Powering off the 
printer while software is loading 
can damage the flash memory.

No action required, but do not power the printer off while code is being 
loaded.

Table 3. Message List

Operator Panel Message

Explanation

Corrective Action

Summary of Contents for Infoprint 6500-v05

































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands