manualshive.com logo in svg

IBM Infoprint 6500-v05, Maintenance Manual


Share
Download
background image

Table of Contents

7

Belt, Platen Open, Adjustment (Figure 25) ............................................................................................................... 371

Paper Scale Alignment (Figure 26) ........................................................................................................................... 373

Platen Gap Adjustment (Figure 27)........................................................................................................................... 374

Ribbon Guide Alignment (Figure 28)......................................................................................................................... 376

Adjusting The End Of Forms Distance ...................................................................................................................... 378

Hammer Phasing Adjustment ................................................................................................................................... 381

Coil Temperature Adjustment ................................................................................................................................... 383

Dynamic Paper Tension Adjustment ......................................................................................................................... 384

Tractor Belt Tension Adjustment ............................................................................................................................... 387

Ethernet Initialization ................................................................................................................................................. 389

6   Parts Catalog ............................................................................................................390

Organization Of This Chapter .......................................................................................................................................... 390

Illustrated Parts Breakdown............................................................................................................................................. 390

7   Preventive Maintenance ...........................................................................................431

Contents .......................................................................................................................................................................... 431

Cleaning The Printer........................................................................................................................................................ 432

Cleaning The Exterior ...................................................................................................................................................... 432

Cleaning The Interior ....................................................................................................................................................... 433

Cleaning The Shuttle Frame Assembly ........................................................................................................................... 434

Cleaning The Card Cage Fan Assembly ......................................................................................................................... 436

A   Installing And Relocating The Printer .......................................................................437

Installing And Configuring The Infoprint 6500 Printer ...................................................................................................... 437

Relocating The Infoprint 6500 Printer .............................................................................................................................. 437

B   Communication Adapters .........................................................................................438

Contents .......................................................................................................................................................................... 438

Ethernet Interface Assembly............................................................................................................................................ 439

Ethernet Troubleshooting Tips......................................................................................................................................... 439

IBM Coax/Twinax Expansion Board ................................................................................................................................ 444

Summary of Contents for Infoprint 6500-v05

































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Infoprint 6500-v05

Oki B2200 Specifications preview
B2200
Brand: Oki Pages: 2
Dascom DP-520 User Manual preview
DP-520
Brand: Dascom Pages: 12
Dascom DP-510 Operator'S Manual preview
DP-510
Brand: Dascom Pages: 19
Dascom DC-7600 Assembly Instructions preview
DC-7600
Brand: Dascom Pages: 5
Panduit LS7 Operator'S Manual preview
LS7
Brand: Panduit Pages: 74
Tally T2380 Specifications preview
T2380
Brand: Tally Pages: 2
Tally Dascom DT-210 Programmer'S Manual preview
DT-210
Brand: Tally Dascom Pages: 57
Fenix SM2000 Operation Manual preview
SM2000
Brand: Fenix Pages: 65
Nantian Electronics PR9 Quick Reference Manual preview
PR9
Brand: Nantian Electronics Pages: 4
Sagem MF9500 Facsimile Operation Manual preview
MF9500
Brand: Sagem Pages: 83
WANHAO Duplicator i3 Software User Manual preview
Duplicator i3
Brand: WANHAO Pages: 24
Xerox VersaLink B415 User Manual preview
VersaLink B415
Brand: Xerox Pages: 324
Kyocera KM-1635 Service Manual preview
KM-1635
Brand: Kyocera Pages: 13
DAKEWE SurePrint S200 Instructions For Use Manual preview
SurePrint S200
Brand: DAKEWE Pages: 94
3Com 3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print... User Manual preview
3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print...
Brand: 3Com Pages: 94
Primera Bravo se Disc Publisher User Manual preview
Bravo se Disc Publisher
Brand: Primera Pages: 58
Pantum M6700D Series User Manual preview
M6700D Series
Brand: Pantum Pages: 164
Fuji Xerox apeosport-v c5585 User Manual preview
apeosport-v c5585
Brand: Fuji Xerox Pages: 493

Brands by name

Popular brands

Load more brands