manualshive.com logo in svg

IBM Infoprint 6500-v05, Maintenance Manual

Share
Download
IBM Infoprint 6500-v05 Maintenance Manual Download Page 336

Hammer Spring Assembly

336

Figure 17. This figure shows how to install a hammer spring assembly onto the hammer bank.

Use new screws from the kit. 
Starting with the inner screws, 
torque the screws to 14 inch-pounds
(1.58 Newton-meters).

New Hammer 
Spring Assembly

NOTE

: The hammer spring assembly shown here is 

for a 6500-v15 printer. Although the number of 
hammer springs and mounting screws varies 
among printer models, removal and installation are 
the same on all models.

Gently press down on the mounting 
base and hold the hammer spring in 
position as you install the screws.

Summary of Contents for Infoprint 6500-v05

































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands