Hyundai HL630VL Operator'S Manual Download | Manualshive

Page: 77 / 161

background image

2-26 Operation Controls

Fig 33

Fig 34

Fig 35

Fig 36

G4. Engine Coolant Temperature Gauge

This gauge displays temperature of engine coolant.

G5. Transmission Oil Temperature Gauge

This gauge displays temperature of oil in transmission
converter and transmission circuit.

Note:

When the pointer indicates red zone, it means the
engine is overheated. Stop the operation, let the
engine run at low rpm and wait for it to cool down.

Do not stop engine. If engine is shut down heat surge
can occur.

Note:

When the pointer indicates red zone, it means the
transmission is overheated. Stop the operation, let
the engine run at low rpm and wait for transmission to
cool down.

Note:

engine error code refer to the attached part.

Display

LCD display the engine fuel consumption, vehicle speed, hour
meter, Amount of fuel remaining, vehicle voltage, engine error
code, overall fuel consumption and mileage.

B. button

the button in on the right side of the LCD. It can make the

buzzer stop warning (pressing more than 3s) and it can
change the display of speed and fuel consumption (pressing
less than 3S).

«
...
75
76
77
78
79
...
»

Summary of Contents for HL630VL


































































































































































Reviews:

No comments

Related manuals for HL630VL

Brand: Landoll Pages: 6

Brand: ParaBody Pages: 9

Brand: ParaBody Pages: 3

Brand: MacDon Pages: 45

Brand: H&S Pages: 30

Brand: Xebex Fitness Pages: 15

Brand: qeedo Pages: 2

Brand: Gardco Pages: 17

Brand: H&S Pages: 42

Brand: Aeroflex Pages: 211

Brand: ZOLL Pages: 48

MIAMI J ADVANCED

Brand: Össur Pages: 35

Brand: Össur Pages: 38

Brand: Össur Pages: 8

Brand: Össur Pages: 72

Brand: Össur Pages: 76

Miami Lumbar Posteo

Brand: Össur Pages: 45

Brand: Össur Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands