manualshive.com logo in svg

Hyundai HL630VL, Operator'S Manual

Share
Download
Hyundai HL630VL Operator'S Manual Download Page 36

Safety 1-27

MAINTENANCE

Warning labels

Warn of that others persons are performing the maintenance, 
and hang the warning sign on cab control device and other nec-
essary places. 
Our company branch organizations provide control warning 
signs.

ARO1330S

1

Fig 28

Fig 29

P e r f o r m  t h e  c l e a n i n g  w o r k  b e f o r e 

maintenance

Perform the cleaning work before inspection and maintenance 
to prevent the dust from entering the machine and ensure the 
maintenance can be securely performed.

If the machine is dirty when it is checked, it is difficult to locate 

the fault, and there is the risk of dust and mud entering the eyes 
or of the personal injury.  Please obey the following items when 
you clean the machine: 
•  Wear the shoes with anti-slippage heels to prevent from 

slipping at the wet places. 

•  Wear goggles and work clothes when you clean the ma-

chine by using HP water gun. 

•  Adopt the protective measures to prevent HP water flow 

from cutting skin or prevent the mud from entering the eyes. 

•  Do not sprinkle water directly onto the electronic compo-

nents (sensors, connectors) (1, Fig. 20). If the water enters 
the electrical system, it will cause the failure or faults.

Pick up any tools in working area, rub up all lubrication oil, oil 
and other lubrication substances, and clean the working area to 
facilitate the safety operation. If the working area is not clean or 
tidy, it will cause tumbling or injury.

Summary of Contents for HL630VL


































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands