manualshive.com logo in svg

Hyundai HL630VL, Operator'S Manual

Share
Download
Hyundai HL630VL Operator'S Manual Download Page 130

Inspection, Maintenance and Adjustment 4-11

ELECTICAL SYSTEM

Note:  

Strictly prohibit disassemble electric circuit and compo-
nents. You should consult the agent to solve such prob-
lems. 

Battery

The electrolyte is the diluted Sulfuric acid which can quickly 
burn the skin and pierce in the clothes. Rinse immediately 
with water if the battery electrolyte spills over your body on 
your clothes for your careless operation.
If the battery electrolytes enter eyes, immediately use plenty 
of water to clean and call a doctor as much as possible. Oth-
erwise, it will cause the person to be blind. 
Drink plenty of water or milk, and eat raw eggs or vegetable 
oils if you carelessly drink the battery electrolytes. And 
immediately go to a doctor or a poisoning prevention center. 
Wear protective goggles when assembling battery. 
The battery can generate Hydrogen. The battery has risk of 
explosion, especially the one without charged. Do not smoke 
near the battery, or perform anything which may cause 
sparks.
Before the maintenance of the battery it is necessary to con-
firm the engine has stop running and the Start switch is at 
OFF  position.
Prevent the accidental short circuit due to the contact 
between battery terminals with metal objects such as tools. 
When disassembling the battery, you should check Positive (+) 
terminal and Negative (-) terminal of the battery. 

When disassembling the battery, you should first disassemble 

Negative (-) terminal. When assembling the battery, you 

should first assemble Positive (+) terminal. 

If the terminal is loose, the bad contact will cause electric 
sparks or arcs, as a result of that the explosion will occur. 
When assembling the battery, you should assemble it 
securely. 

WARNING

Battery in cold weather

The battery will consume a lot when performing starting and 
pre-heating operation in cold weather. Meanwhile, when the 
temperature decreases, the performance of the battery will also 
decrease. 
In extremely cold weather, it is possible to remove the battery 
and put it in a warmer place, thus helping the improvement of 
battery performance. 

Summary of Contents for HL630VL


































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands