manualshive.com logo in svg

Hyundai HL630VL, Operator'S Manual

Share
Download
Hyundai HL630VL Operator'S Manual Download Page 41

1-32 Safety

Avoid being crushed or cut

When performing maintenance,if you must operating the engine, 
ensure at least two persons must work together. One person is 
sitting on the driver seat to operate the control device and shut 
off the engine. 
Unless otherwise instructed by others, Do not adjust the ma-
chine when the machine or the engine is running. 
Be far away from the running or moving parts.
Keep objects far away from the fan blades which may throw off 
or cut the objects. 
Do not use bent or peeled cables. When handling the cables, 
please wear the gloves.

The  dowels  will  fly  off  when  you  knock  them.  The  flied  dowel 

may cause the personal injury. Ensure that there is nobody 
around when you knock the dowels. Wear the protective gog-
gles when you are knocking to prevent the eyes from being hurt. 

Equipment supports and stops

Do not let any load and equipment hang in the air. Please lower 
all objects down to ground before you leave the cab. Do not use 
hollow, cracked, unstable or rocking objects to support. Never 
work under the equipment supported only by a jack.

Fig 35

Summary of Contents for HL630VL


































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands