background image

Operation 3-27

ON THE LAST PAGE OF OPER-

ATION UNDER SPECIAL CONDI-

TIONS,INSERT

Working in Water

After working in water,lubricate all lubrication points on front and 
rear frames which have been under water so water is removed.

The water depth is an important factor to take into consiertation 
when the machine is working in swampy areas.Do not enter 
water whose depth exceeds the machine’s minimum ground 
clearance height or is high enough to wet the bottom of the axle 

housing.

As a rule of thumb, the allowabel water depth is about 
400mm(16 inches).This means that the machine should not be 
used in a river.

Observe the following conditions:

1.  Check the water depth in advance when crossing a river.

2.  Use the same precautions before crossing across a 

swampy area.

3.  Do not enter rivers whose riverbed in steep or has a rapid 

flow.

Aviod use of the loader in salt water.Salt water will cause the 
development of rust which will shorter the life of loader. 

IMPORTANT

Summary of Contents for HL630VL


































































































































































Reviews: