Hyundai HL630VL Operator'S Manual Download

Page: 44 / 161

Safety 1-35

BATTERY

Prevention of battery risks

The battery electrolytes contain sulphur acid, and battery can
produce Hydrogen. Hydrogen is highly explosive. If disposing

incorrectly, it will cause serious injury or fire. In order to prevent

theses problems, please accomplish following items:

Prohibit smoking or flame approaching the battery.

• Please wear protective goggles and rubber gloves when you

performing inspection, maintenance or charging of battery.

• Rinse immediately with water if the battery electrolytes spills

over your body on your clothes.

• Rinse with plenty of water and see the doctor immediately if

the battery electrolytes enters your eyes.

• Drink plenty of water or milk, and eat raw eggs or vegetable

oils if you carelessly drink the battery electrolytes. And im-
mediately go to a doctor or a poisoning prevention center.

• Please use clean wet cloth to scrub the upper surface of the

battery. Do not use gasoline, diluent, other organic solution
or detergent.

• Tighten the cover of battery box.
• If the battery electrolyte is frozen, do not charge the battery

or use other power supply to start the motor, otherwise it will
cause the risk of explosion.

• If you want to charge the battery or use other power supply

to start the motor, you should let the battery electrolytes
molten and check for the leakage before operation.

• Remove the battery from the machine before charging.

Fig 38

Summary of Contents for HL630VL


































































































































































Search results

Summary of Contents for HL630VL

Reviews:

Related manuals for HL630VL

Brands by name

Popular brands

Hyundai HL630VL, Operator'S Manual

Search results

Summary of Contents for HL630VL

Reviews:

Related manuals for HL630VL

Brands by name

Popular brands