Hyundai HL630VL Operator'S Manual Download

Page: 144 / 161

Transportation 5-3

Incorrect lifting may cause the offset of the machine, thus
inducing personal injury or death as well as property loss.

WARNING

LIFTING MANCHINE

1. It is necessary to let the professionals with lifting knowl-

edge be responsible for the command and operation.

You should calculate the crane’s maximum lifting weight

and the sling’s bearing capacity to ensure the lifting safety.
Meanwhile, the 4 hooks on the sling shall bear load evenly.

3. Accomplish the following preparation before lifting:

• Put the shifting manipulating handle on “Neutral Gear”

position, and put the neutral gear locking plate on
“Locking” position.

• Put the movable arm and bucket to the lowest position.
• Pull up the button of parking brake to apply parking

braking.

•  Switch off the engine and pull out the electric button
•  Close and lock all doors.
•  Toggle the power supply Negative switch to “OFF” po-

sition.

•

Use frame to fix the bumper and fasten the front and

rear frames, making the machine unable to rotate.

The sling should be securely fixed to the lifting eyes of

the machine on which the lifting marks are indicated. ing
during transportation.

Fig 4

Summary of Contents for HL630VL


































































































































































Search results

Summary of Contents for HL630VL

Reviews:

Related manuals for HL630VL

Brands by name

Popular brands

Hyundai HL630VL, Operator'S Manual

Search results

Summary of Contents for HL630VL

Reviews:

Related manuals for HL630VL

Brands by name

Popular brands