Hyundai HL630VL Page 93 Operator'S Manual Download | Manualshive

Page: 93 / 161

background image

3-2 Operation

Lubrication oil and filter element

1. Change oil and renew filter element after working for first

50 hours.

2. Change transmission oil after working for first 100 hours.
3. Change the filter element in hydraulic oil line and renew

filter element after working for first 250 hours.

4. Change axle gear oil after working for first 100 hours.

Note:

Refer to “Inspection, Maintenance And Adjustment” on

Page 4-1 of this manual for replacement of lubrication oil

or grease.

Running-in of the new vehicle

Running-in of the new vehicle plays an important role in extend-
ing the operation life, eliminating fault and hidden troubles, as
well as avoiding major faults. After buying this machine, the user
must perform the machine operation and maintenance accord-

ing to the regulations on the running-in of new vehicles specified

in this manual, and then you can normally use this machine.

Requirements on running-in of the new

vehicle

1. The period for running-in of the new vehicle is 100 hours.
2. Start the engine and run at idle for 5 minutes.
3. During the running-in period, you should evenly arrange the

running-in test for each gear of Forward

ⅠⅡⅢ

and

Ⅳ

Re-

verse

ⅠⅡ

and

Ⅲ

Gears.

4. Run the vehicle in a sequence at low speed (small power)

first, and then at a high speed gradually. Except in emergen

-

cy, you should avoid sudden start, acceleration, steering and
abrupt braking.

5. It is appropriate to operate the vehicle with a load of loose

materials during the running-in period, without too abrupt or
too urgent actions. During the running-in period, the loaded
weight should not exceed 70 % rated load, and the travel
speed should not exceed 70% rated maximum speed.

6. Pay attention to the lubrication of the machine, change the

lubrication oil and lubrication grease as per the specified in

-

terval.

7. You must pay attention to the temperatures of gearbox,

torque converter, front/rear axles, hubs, parking brake, imme-

diate supporting shaft, and hydraulic oil, cooling fluid, engine

oil. Perform the troubleshooting if the overheat phenomenon
is found.

8. Check bolt and nut of each component for the tightening.

«
...
91
92
93
94
95
...
»

Summary of Contents for HL630VL


































































































































































Reviews:

No comments

Related manuals for HL630VL

Brand: JBL Pages: 15

Brand: YYZ Lighting Pages: 3

Brand: Camp Safety Pages: 118

Brand: Ultrafast Systems Pages: 39

Brand: Mackworth Pages: 2

Brand: Ocmis Irrigazione Pages: 100

Brand: Farmet Pages: 102

Brand: Gainsborough Pages: 2

Brand: Gainsborough Pages: 2

Brand: Gait up Pages: 12

Brand: Gait up Pages: 6

Brand: Gaiam Pages: 2

Brand: Haaga Pages: 31

Brand: Landoll Pages: 70

Brand: Landice Pages: 19

Brand: Landice Pages: 7

Brand: Ideal Heating Pages: 16

Zen-O lite RS-00600

Brand: GCE Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands