background image

1-36 Safety

Auxiliary starting or charging the engine 

battery

The incorrect connection of battery cables may cause explosion 

or fire. Please obey the following items:

•  Switch off all electrical equipments before connecting to 

battery, including the electric switch for battery charger and 
auxiliary starting device. 

•  When using other machine to perform the auxiliary starting, 

Do not let two machines contact each other. Wear protective 
goggles when connecting battery.

•  24 V battery combination consists of two 12 V batteries 

in serial. One wire connects to the Positive pole of one        
battery and the negative pole of the other battery. Connect 
the two positive poles of two batteries not in serial connec-
tion, and connect the negative pole of the booster battery 
and the metal support for the charged equipment. Refer to 
the  methods and description of in “Start Engine by Using 
Booster Battery” on Page 3-8. 

• 

When connecting wires, first connect the positive pole wires; 

when disconnecting wires, first disconnect the negative 
pole wires. Finally connect the negative pole of the booster     
battery and the metal support for the charged equipment. 
The connection shall be as far away from the battery as 
possible.

Fig 39

Summary of Contents for HL630VL


































































































































































Reviews: