Hyundai HL630VL Operator'S Manual Download

Page: 48 / 161

Safety 1-39

Lifting of loader

1. It is necessary to let the professionals with lifting knowledge

be responsible for the command and operation.

2. You should calculate the crane’s maximum lifting weight

and the sling’s bearing capacity to ensure the lifting safety.
Meanwhile, the 4 hooks on the sling shall bear load evenly.

3. Accomplish the following preparation before lifting:

• Put the shifting manipulating handle on “Neutral Gear”

position, and put the neutral gear locking plate on “Lock-
ing” position.

• Put the arm and bucket to the lowest position.
• Pull up the button of parking brake to apply parking

braking.

•  Switch off the engine and pull out the starter key.
•  Close and lock all doors.
•  Use frame-fixed bumper to fasten the front and rear

frames, making the machine unable to rotate.

4. The sling should be securely fixed to the lifting eyes of the

machine on which the lifting marks are indicated.

Incorrect lifting may cause the offset of the machine, thus
inducing personal injury or death as well as property loss.

WARNING

Summary of Contents for HL630VL


































































































































































Search results

Summary of Contents for HL630VL

Reviews:

Related manuals for HL630VL

Brands by name

Popular brands

Hyundai HL630VL, Operator'S Manual

Search results

Summary of Contents for HL630VL

Reviews:

Related manuals for HL630VL

Brands by name

Popular brands