Hyundai HL630VL Page 46 Operator'S Manual Download

Page: 46 / 161

Safety 1-37

TOWING

Matters needing attention on towing

If fault occurs during the selection or inspection of the traction
string or during performance of traction, it will cause serious in-
jury. Please obey the following items:
• Use the methods introduced in Operation and Maintenance

Manual.

• Please wear the leather gloves for disposing string and

ropes.

• When there are two or more persons to do the preparation,

unify the signals and use them correctly.

• If there is fault in the machine or in the brake system, or the

engine could not be started, please contact with the agent.

• When performing the traction operation, do not walk

between the tractor and the towed machine.

• It is dangerous to perform the traction on slope, therefore,

you should select a gentle slope. If there is no gentle slope,
please reduce the slope angle before performing traction
operation.

• Please use the string and ropes with enough traction force

to tow the fault machine.

• Do not use the worn, kinked rope or the rope with too small

cross-section.

Summary of Contents for HL630VL


































































































































































Search results

Summary of Contents for HL630VL

Reviews:

Related manuals for HL630VL

Brands by name

Popular brands

Hyundai HL630VL, Operator'S Manual

Search results

Summary of Contents for HL630VL

Reviews:

Related manuals for HL630VL

Brands by name

Popular brands