Husqvarna F2303Q0 Repair Manual Download Page 66

Page: 66 / 322

9 SHOCK ABSORBER, LINK FORK

Mount screw

but do not tighten yet.

Guideline

Screw, bottom

M10

shock absorber

•

Info

60 Nm (44.3 lbf ft)

Loctite

2701

Raise the wheel slightly to be able to mount the screw

more easily.

Position the linkage lever.

Mount and tighten fitting

Guideline

Nut, linkage lever to

M 14x1 .5

angle lever

Info

80 Nm (59 lbf ft)

Raise the wheel slightly to be able to mount the screw

more easily.

- Tighten screws

Guideline

Screw, bottom

M10

shock absorber

- Tighten fitting Ci).

Guideline

Nut, angle lever to

link fork

Finishing work

M14x1.5

60 Nm (44.3 lbf ft)

Loctite

2701

80 Nm (59 lbf ft)

Remove the motorcycle from the lift stand. (

p. 12)

Servicing the shock absorber

Caution

Risk of injury

Parts of the shock absorber will move around if the shock absorber is detached incor

rectly.
The shock absorber is filled with highly compressed nitrogen.

Please follow the description provided.

Condition

The shock absorber has been removed.

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands