Husqvarna F2303Q0 Repair Manual Download Page 263

Page: 263 / 322

IGNITION SYSTEM 21

Stator winding - check the short circuit to ground {terminal 31)

Measure the resistance between the specified points.

Alternator, connector

- Measuring point

Ground

{-)

Resistance

21.5

21.6

If the displayed value does meet specifications:

Change the stator.

Removing the stator

D00343-10

Installing the stator

Condition

The alternator cover has been removed.

Remove screws

Remove the retaining bracket.
Remove screws

Remove rubber grommet

from the alternator cover.

Remove the stator from the alternator cover.

Position the stator in the alternator cover.
Mount and tighten screws

Guideline

Screw, stator

6 Nm (4.4 lbf ft)

Loctite

243

™

D00343-11

Position the retaining bracket.
Mount and tighten screws

Guideline

Crankshaft

speed sen-
sor screw and
cable retainer

6 Nm (4.4 lbf ft)

Loctite

243

™

Position rubber grommet

in the alternator cover.

261

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands