Husqvarna F2303Q0 Repair Manual Download Page 194

Page: 194 / 322

17 ENGINE

17.4.4

17.4.5

spring length of the oil pressure control valve, checking

Preparatory work

306115-10

- Remove the oil pressure control valve. (

p. 191)

Main work

- Measure the spring length of the oil pressure control valve.

Oil pressure control valve

Minimum length of pres- 122.1 mm (0.87 in)

sure spring

If the measured value does not meet specifications:

- Change the spring.

Finishing work

- Install the oil pressure control valve. (

p. 192)

oil pressure control valve, installing

- Insert ball

and pressure spring

Mount and tighten screw plug

with sealing washer

C,.

Guideline

Screw plug, oil pres- M12x1 .5

sure control valve

20 Nm (14.8 lbf ft)

•-•

.""-

•-

•

17.4.6

17.4.7

192

310047-11

crankshaft seal ring in the clutch cover, changing

B03798-10

Removing the water pump

- Remove lock ring

- Remove crankshaft seal ring

- Press the new crankshaft seal ring into the clutch cover with

the open side facing inward until it is flush.

- Mount lock ring

- Grease the sealing lip.

- Remove nut

- Remove water pump impeller

Info

If the water pump impeller cannot be detached, then

the water pump shaft can be pressed out toward the

inside.

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands