Husqvarna F2303Q0 Repair Manual Download Page 235

Page: 235 / 322

17.5.21 Installing the timing chain

ENGINE 17

Mount internal rotor

and external rotor

✓ The rounded sides of the external rotor face the engine

case.

Position oil pump cover (D. Mount and tighten screws@.

Guideline

Screw, suction
pump cover

6 Nm (4.4 lbf ft)

Loctite

243

™

Thread in the timing chain and place it over the timing chain
sprocket.

•

Info

If the timing chain was used before, ensure it is run

ning in the correct direction.

Position the timing chain securing guide.
Mount and tighten screw

Guideline

Screw, timing

10 Nm (7.4 lbf ft)

chain securing

Loctite

243

™

guide

Thread in timing chain tensioning rail

from above.

Mount and tighten screw

Guideline

Screw, timing

10 Nm (7.4 lbf ft)

chain tension-

Loctite

243

™

ing rail

233

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands