Husqvarna F2303Q0 Repair Manual Download Page 110

Page: 110 / 322

12 FUEL TANK, SEAT, TRIM

R00449-10

108

- Position the new fuel pump.

- Mount nut

with gasket, but do not tighten yet.

- Pull out the fuel pump.

✓ The fuel filter remains in the fuel tank.

•

Info

Make sure that the fuel filter is not pulled out too far.

- Keep the fuel pump with hose tensioned, turn clockwise and

position.

✓ The hoses in the tank are located in the left half of the

tank.

✓ The connector points downwards.

- Mount and tighten screws

@).

Guideline

I Screw, fuel pump

EJOT

2.3 Nm (1.7 lbf ft)

- Mount fuel connection

with the gasket but do not tighten

yet.

- Tighten nut

Guideline

Nut, fuel pump fas

tener

M12x1.75

- Tighten fuel connection

Guideline

Fuel connection on

fuel tank

Finishing work

M8x1 .25

- Install the fuel tank. (

p. 103)

- Mount the seat. (

p. 101)

15 Nm (11.1 lbf ft)

10 Nm (7.4 lbf ft)

Summary of Contents for F2303Q0



































































































































































































































































































































Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands

Husqvarna F2303Q0, Repair Manual

Search results

Summary of Contents for F2303Q0

Reviews:

Related manuals for F2303Q0

Brands by name

Popular brands